Repair Whirlpool Error F31 (Solved)

Home > Whirlpool Duet > Whirlpool Error F31

Whirlpool Error F31

Contents

Submitted: 5 years ago. Press PAUSE/CANCEL twice to clear the display. Believe it or not I have a job too!I answered your question. Door lock mechanism is broken. weblink

F06 STEAMER DEFECT The Steamer temperature has not reached the correct value. This fault code only appears during diagnostic mode. Thanks for counting on us to help with your appliance problem. PUMP DRIVE ERROR The pump driver fails to activate.

Whirlpool Cabrio Dryer Fault Code F31

Check dispenser motor for powered rotations. Ft. Check probe.

Ok let me ask you this Which bard did you replace in this unit?The one in the front or the one on the leftside of the unit looking at it from Check the electrical connections at the pump and make sure the pump is running. 4. After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. Whirlpool Duet Washer Error Codes F31 Check harness on steamer electronic board. 2.

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the Whirlpool Duet Dryer Error Code L2 I don't know where red and black goes to on the control? Press and hold any key for 1 minute to clear R failure code from memory. http://www.justanswer.com/appliance/4kqk2-whirlpool-duet-front-load-washer-placed-bulky.html Check the pressure switch for proper operation.

Ask Your Own Appliance Question Customer: replied1 year ago. Whirlpool Cabrio Dryer L2 Error Code Check the motor and do a continuity test. 3. Check the connections between the Steamer 3. I will be able to start testing things tonight around 8:00 or 9:00 which is after your time I know but maybe you can give me a couple things to be

Whirlpool Duet Dryer Error Code L2

Unplug washer or disconnect power. 3. this page F03 HEATER SC TO GROUND The Heater has a internal short circuit. Whirlpool Cabrio Dryer Fault Code F31 F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Whirlpool Duet Dryer F 31 Ask Your Own Appliance Question Customer: replied1 year ago.

Replace heater. have a peek at these guys Check the drain hose and make sure it is not plugged or kinked. 2. This should clear the unit of the excess detergent. 1. Opening the lid will allow you to view and redistribute the load. Whirlpool Washer F31 Code

F23 HEATER FAILURE If the temperature increase during the first 40 minutes is less than 86°F (30°C). 1. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. This fault code will ONLY appear when in the diagnostic test mode. check over here F65 STEAMER TIME OUT REACHED Error happens if there is no communication between Central Control Unit (CCU) and steamer electronic board.

Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Whirlpool Cabrio Dryer Troubleshooting Codes Press PAUSE/CANCEL two times to clear the display. 1. There is a drain catch inside the washer that you will want to access and clean if you're getting this drain error.

Check for continuity of the User Interface harness. 2.

Plug in washer or reconnect power. 5. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Check for continuity of the User Interface harness. 2. Whirlpool Duet Dryer Error Codes Check drain pump. 7.

Check drive motor tachometer resistance. Check all hoses for possible leaks. 6. F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure http://compaland.com/whirlpool-duet/whirlpool-fh-error.html This fault code only appears in the diagnostic test mode.

Relist: Other.Completely terrible experience with this technician! Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. A power glitch may cause this error.

Check the water temperature sensor and connection to it. 3. C. Check the drive motor for powered rotations. 6. In this case, replace control board (also called ERC or clock).

Check door switch/lock unit for foreign objects. 2. Still need help? F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs. Check wire harness connections to the User Interface and the Central Control Unit. 3.

codes. I tested continuity on the heater element and while running I tested the red wire to a ground wire and the frame and got 140 actually. Ask Your Own Appliance Question Customer: replied1 year ago. F99 NOT SUPPORTED User selected on the UI the unsuppor ted Cycle on the CCU.

Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. test L1 Black and L2 Red at the terminal block and turn the unit on and try to start it! F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1. Replace MCU board.

Front-Loading... 240 Questions Whirlpool Duet Sport HT WFW8400TE Washer 288 Questions Whirlpool Duet 4.0 Cu.