Fix Whirlpool Duet Ht Washer Error Code Fh Tutorial

Home > Whirlpool Duet > Whirlpool Duet Ht Washer Error Code Fh

Whirlpool Duet Ht Washer Error Code Fh

Contents

There should be a clip that keeps both tubes clamped to the back of the washer so the tubes are kept away from the machine rubbing on them. Video should be smaller than 600mb/5 minutes Photo should be smaller than 5mb Video should be smaller than 600mb/5 minutesPhoto should be smaller than 5mb Related Questions Whirlpool duet washer error? customer now tells me it reads hf intermitantly +stops after 2minutes in beginning wash. Published on 10 Jul 2013Service your Maytag Washer that has some of the following problems: Error codes fh, f9By visiting us at http://www.appliancevideo.comTo do the repair use a W10514214 Pressure SwitchMaintenance, weblink

Water Inlet Valve Testing – Washing Machine Troubleshooting & Repair - Duration: 2:51. I'm thinking that the pressure switch could be the problem but before I buy it I'd like to get an opinion if that is likely or if it is something else. Are you using HE High Efficiency detergent? Thanks!!!! http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/400-5-620619-/Whirlpool-F-H-FH-No-Water-Entering-Machine-or-Pressure-Switch-Failure-

What Does Fh Mean On A Whirlpool Washer

Make sure that both valves at the water source(s) are turned on all the way. 2. On my washer, I kept getting HF messages, and found that the reed switch remained open (no conduction), even when a magnet was held against it. Potential Causes If there is no water in the unit:

—Make sure that both valves at the water source(s) are turned on all

the way. —Check for plugged or kinked inlet

Answer Questions Is there a way to shut off two of the thermostats in my house so I don't waste oil heating empty floors? (The baseboards have antifreeze)? As further information, I checked the water lines and they get good water flow. If this happens the water inlet valve or the water level pressure switch may be defective. Whirlpool Duet Pressure Switch Miller I have been having the same issue with my washing machine.

I've been google searching for THREE DAYS following our overfilled washing machine spilling out on us! Whirlpool Duet Flow Meter Finally, if all other things check out, the problem might be with the central control unit circuit board (CCU) or the wiring to any of these components. Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread!

All rights reserved. © Applianceblog.com 2004 - 2016 Remind me later Review A privacy reminder from YouTube, a Google company Skip navigation GBUploadSign inSearch Loading... Whirlpool Duet Diagnostic Mode Call our Parts Department now! 877-803-7957 Back To Top You have chosen to ignore HAMMER. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com #2 (permalink) 01-05-2009, 05:32 PM kayakcrzy Senior Expert APP Volunteer Join Date: Feb 2008 Location: Look closely with a flashlight and maybe you will find like me that the washer when out of balance would occasionally hit and rub those two tubes.

Whirlpool Duet Flow Meter

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3.

How to run diagnostics in on the tech sheet inside of the washer and the dryer. What Does Fh Mean On A Whirlpool Washer Find out more » Total: $263.10 Add to Cart Cause 5 Pressure Switch Parts Pressure Switch for your Whirlpool Washing Machine RepairClinic Item #2684743 Water level pressure switch $50.65 Quantity: In Ghw9150p Errorcodes Press PAUSE/CANCEL twice to clear the display.

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the http://compaland.com/whirlpool-duet/whirlpool-duet-washer-error-code-e01-f09.html Since the only steps flagged were those where water was supposed to be added, it sounds like a bad water inlet valve, right? disclaimer and Terms of Use. Top 5 Reasons Top-Load Washer Won’t Fill? Fh Error Code Maytag Washer

I now have both an overpriced spare water inlet valve and flowmeter that the parts store won't take back. As for you Pebbles, I suspect that your pump is partially plugged and not allowing a complete discharge within the allotted time. Call our Parts Department now! 877-803-7957 Back To Top Posted: Sat Aug 20th, 2005 05:45 pm 4th Post Pegi Fellow, Academy of Sublime Masters of check over here All rights reserved.

Then, consider replacing the flow meter. Whirlpool Duet Error Codes then at other times it will complete the entire wash as if there is nothing wrong, maybe there is a siphoning problem,i will try replacing flow meter __________________ - #8 Looking for help.

If Pause/Cancel does not work: Unplug the washer or disconnect the power for one minute.

Inside the inletvalves are screens.Remove any accumulated film or particles from the screens. Its possibly a bad flowmeter, here's the one for your model: Whirlpool WPW10110225 Flowmeter Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 This code can also display if the machine is filling with water, the flow meter measures 10.5 gallons of water into the machine, but the water level pressure switch does not Whirlpool Duet Washer Parts If the water pressure is too low, the washer may not properly operate.To find out your exact pounds-per-square-inch (psi) value, contact your local water utility company.

Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Loading... RepairClinic.com 361,903 views 2:51 Maytag Washer not draining code F02 or F2 - Duration: 7:36. this content Help Remember Me?

The circuit boards carry a two year warranty also. Is the water pressure less than 10 psi? Saved a few hundred dollars here and fixed it myself. :)Hope this helps someone else. NOTES: On some washers, when the washer is started for the first time after this error code, it will begin to drain.

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Choose your language. If I press pause/cancel twice and unplug it, often it will work OK for the rest of the cycle (but not always). You can try chatting with one of our friendly associates.