(Solved) Whirlpool Duet Error Messages Tutorial

Home > Whirlpool Duet > Whirlpool Duet Error Messages

Whirlpool Duet Error Messages

Contents

Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Check Drive belt Check MCU Check Motor Check Wire Harness Sud SUDS LOCK (Overdose of Detergent detected This is a bad one… Duet washer main control error. If failure still present: 3. Press PAUSE/CANCEL two times to clear the display. 1. http://compaland.com/whirlpool-duet/whirlpool-duet-f28-error.html

Iniciar sesión 516 22 ¿No te gusta este vídeo? Unplug washer or disconnect power. 3. See the repair guide to fix it yourself Motor control board, Wiring harness F/11 Serial communication error between main electronic ontrol board and motor control board Check the connections on the eSpares 27.081 visualizaciones 5:50 Whirlpool Duet Sport Washer, will not drain - Duración: 10:00.

Whirlpool Duet Washer Error Codes F21

Door switch/lock unit failure. 1. If the Duet successfully runs 10 cycles in a row with no fault the error will be cleared from the washer's memory, so any errors you see are likely new and Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way.

JPlovesLIFE 25.671 visualizaciones 7:35 Whirlpool duet f21 error fix - Duración: 4:32. Possible causes… 1. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Whirlpool Duet Dryer Error Codes Exchange Steamer if it is totally blocked.

heli400 243.373 visualizaciones 4:39 Washing Machine Drain Pump Replacement - Duración: 10:09. F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down. Replace failed component. ^ top F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. try here NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

If you can’t look through it, exchange Steamer. 5. Whirlpool Duet Washer Error Codes F02 NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. A power glitch may cause this error. A double oven will have two of each switch and one common wire. 1.

Whirlpool Duet Reset

Door switch open while door is locked. 1. https://www.reference.com/home-garden/whirlpool-duet-washer-error-codes-4c617adc644657d6 Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect Whirlpool Duet Washer Error Codes F21 Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. Whirlpool Duet Washer Error Codes F20 The drain/filter/pump is right in front.

Unplug washer or disconnect power. 3. have a peek at these guys If corrections are made in any step, reconnect power to control. Refer to the Water Temperature Sensor section. If the above does not correct the problem, replace the pump. Whirlpool Top Load Washer Error Codes

Subscribe ApplianceAssistant on Youtube! Search Site For Parts Call (877) 338-6774 Like ApplianceAssistant on Facebook! Sign In Register Keep model on this computer temporarily This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future. Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Check Drive belt Check MCU Check Motor Check Wire Harness Sud SUDS LOCK (Overdose of Detergent detected check over here Repairclinic.com Appliance Newsletters Purchase Info for Appliance Parts & Manuals » Need Parts?

Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Join our VIP email list and Whirlpool Washer Error Codes 5d Verify CCU operation by running a Diagnostic Test or any cycle. Check the electrical connections at the pump and make sure the pump is running.

Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU).

If there are no problems, you usually need to replace the door lock assembly. Make sure you are using HE or High Efficiency detergent. NOTE: The door switch/lock unit can be manually unlocked. Whirlpool Duet Washer Error Code F11 If door not latched: Disconnect power from unit.

Error Code Possible Solution dET The detergent dispenser cartridge is not detected in the dispenser (only on select models).If you are usingsingle-load doses of detergent, ignore this message. If all connections are good, then check the individual switches as outlined for the F5 failure. ^ top 2 Digit Failure Codes F0 Board failure Replace control board (also called ERC Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 4. this content Acción en curso...

Replace MCU board. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. Check the electrical connections at the pump and make sure the pump is running.

If the wiring and the drive system are sound, the motor control board usually needs to be replaced. Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure My daughter was doing a load Press STOP/CANCEL to clear the display. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check Drain Pump Check Pressure Switch Check CCU F/dL

In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. If the above does not correct the problem, replace the pump. F02 error could be caused by the over use of soap, you need to make sure your using 2 tablespoons of HE soap, 1/4 cap at the most. Check Wire Harness connectors to the MCU, and Central Control Unit (CCU) Check the Drive system for any worn or failed components Check MCU Check Motor F/11 Serial Communication Error Communication

It also means unplug the washer so you don't get electrocuted! Press PAUSE/CANCEL twice to clear the display. Plug in washer or reconnect power. 6. Verify CCU operation by running a Diagnostic Test or any cycle.

Check mechanical linkage from dispenser motor to the top of the dispenser. Sarasota, FL "Best customer service experience I ever had." Christine G.