(Solved) Whirlpool Duet Electric Dryer Error Codes Tutorial

Home > Whirlpool Duet > Whirlpool Duet Electric Dryer Error Codes

Whirlpool Duet Electric Dryer Error Codes

Contents

Published on 27 Oct 2013Dryer not working , main control panel bad connection check control board. The lid switch must be opened at least once before restarting the cycle, if this condition occurs. Items received damaged must be reported within 10 days of receipt. I have only owned the dryer for two weeks. weblink

Use a multi-meter and check the resistance of that particular thermistor/temp sensor (10,000 ohms). Unplug dryer or disconnect power. 2. Perform the Console Buttons and Indicators Diagnostic test to verify repair. Check the wire harness connections between the main electronic control board and the user interface control board assemblies.

Whirlpool Duet Dryer Error Codes F01

Plug in dryer or reconnect power. 3. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running. Remove the four screws from bottom of the duct in rear.

Plug in dryer or reconnect power. 2. This may signify problems with the drive motor, thermal protector or motor controller. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU Whirlpool Duet Dryer Error Codes E1 Check the MCU by looking for operations of the drive motor and check the drive motor for powered rotations.

Press START to continue the cycle, or press PAUSE/CANCEL to clear the display. Whirlpool Duet Dryer Error Codes F70 Remove power from the dryer. The diagram you want to be looking at is the "Dryer Cabinet" diagram.

November 13, 2014 Refrigerator Has Power and Lights But Not Blowing Cold Air November 13, 2014 Best Rated Memory Foam Mattresses For Back & Neck Pain Relief November 8, 2014 Car

Press 'Stop/Cancel' to clear display. Whirlpool Duet Dryer Control Board F15 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). FdU Door unlock error A Door Unlock Error occurs if the door cannot be unlocked. Press and hold any key for 1 minute to clear R failure code from memory.

Whirlpool Duet Dryer Error Codes F70

Contact Recent Posts Whirlpool Gas Dryer Igniter Replacement Whirlpool Cabrio dryer F1 error code fix How to Fix Dryer Heating Element Where is the heating element on a Whirlpool Dryer? http://dryernotheating.net/whirlpool-duet-dryer-error-codes/ Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. Whirlpool Duet Dryer Error Codes F01 Do this to be certain - Duration: 2:23. Whirlpool Duet Dryer Diagnostic Mode April 29, 2016 Bathroom Sink Drain Pipe Is Leaking - How To Fix - What To Check?

If the button cannot be unstuck then replace the user interface control assembly. have a peek at these guys If the outlet thermistor is defective, replace it. December 9, 2015 How To Remove Candle Wax From Your Carpet In 3 Easy Steps December 8, 2015 Fisher & Paykel AquaSmart Top Load Washing Machine Error Codes December 7, 2015 Check all connections at control board and at the latch switch and door switch. Whirlpool Dryer Error Codes

Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. I can't find anything documentation describing what the code means. F1-E4 - Model ID Error - Disconnect power for at least 30 seconds and then reconnect. check over here UNPLUG DRYER WHILE WORKING ON IT.update keep your dryer top surface clear of anything on top of it.

If this doesn’t happen, go to step 3. Whirlpool Duet Sport Dryer Control Board Check connections at control and at the latch switch and door switch. 2. Press 'Stop/Cancel' to clear display.

More Fun Back To Fault Codes Admiral Fault Codes Whirlpool Appliance Fault Codes Roper Fault Codes Gibson Appliance Fault Codes Hotpoint Appliance Fault Codes Kelvinator Appliance Fault Codes KitchenAid Appliance Fault

VideoJoeKnows 436,524 views 13:36 Duet Dryer Drum Belt (part #661570V) - How To Replace - Duration: 9:13. Press and hold any key to clear the error code and F2 code should appear. While the dryer is running during this procedure, pressing the Start button again should turn the motor and heater off, and the display to again show “88.” If a diagnostic procedure How To Reset Whirlpool Duet Dryer A wiring problem or drive motor failure could also prevent the dryer from continuing to run properly.

Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check April 24, 2014 Understanding Military Time With Informative Charts April 23, 2014 How To Make A DIY Deck Rail Garden Planter From A Pallet April 21, 2014 50 Bedroom DIY Decorating Repeat steps A and B for door switch. 3. this content Sign in Transcript Statistics 101,570 views 344 Like this video?

NOTE: The inlet thermistor is part of the high limit thermostat on this dryer. If the connections are okay then the main electronic control board and the user interface control assemblies may need to be replaced. Check the belt switch and drive motor. OK, Continue Getting your parts... 24/7 Customer Support Call 1-877-477-7278 Sign In About Us Repair Forum My Account Order Status Shop for Parts Get Repair Help CHECKOUT Items in Cart: Total

Whirpool Duet Front Loading Gas and Electric Dryer Fault Codes PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Reconnect power and plug unit in. October 6, 2016 Dishwasher Door Will Not Close or Latch - How To Fix? If damage is found, replace appropriate part.

Check sensor, sensor harness and sensor harness connection at sensor and oven control. codes. I had so many questions and they answered them all." Sharon S. Check that the power cord is firmly connected to the dryer’s wire harness. 4.

F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Unplug the unit to service.