Repair Whirlpool Error F-1 (Solved)

Home > Whirlpool Cabrio > Whirlpool Error F-1

Whirlpool Error F-1

Contents

If it starts normally, push Pause/Cancel, replace the bottom front cover, and you should be good to go. Virginia Beach, VA "Your service people are so friendly and helpful. Check the connections between the Steamer 3. CA or CI Average current limit or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return http://compaland.com/whirlpool-cabrio/whirlpool-f51-error.html

Unplug washer or disconnect power. 2. If too much detergent was used: Run the unit through a RINSE/SPIN cycle. Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. Confirm water supply to steamer. 5.

Whirlpool Cabrio F1 Error Code Recall

This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). 4. Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets.

Check Steamer for continuity (Abnormal =infi nity). 2. Press STOP/CANCEL to clear the display. Remove clothes from drum and start the cycle again. Whirlpool Dryer F1 Error Code RepairClinic.com 327,107 views 4:56 Cabrio - Bravos -Oasis F1 Error Washer Repair - Duration: 2:19.

With this failure, power to the motor controller cannot be turned off by the machine controller. Whirlpool Washer Cabrio Recall Was wondering if anyone has tried to repair the ccu. Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx Check the MCU by looking for operations of the drive motor. 7.

Door switch/lock unit failure. 1. Whirlpool Cabrio F1 Recall 2013 F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. Secure the mounting screw. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4.

Whirlpool Washer Cabrio Recall

WHIRLPOOL FAULT CODES Whirlpool Duet Front Loading Automatic Washer Fault Codes Failure Code Fault Code Description Solution FH No water detected entering machine or Pressure switch trip not detected. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Yes No Voted Undo Score 6 Cancel Comments: An Luther then the f1 error code at the same time e9 appears an door will not open 11/28/2015 by mbjkluv1 Add a Whirlpool Cabrio F1 Error Code Recall Unplug washer or disconnect power for two minutes. Whirlpool Cabrio Dryer F1 F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.

F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. have a peek at these guys To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. Door installation. Press STOP/CANCEL to clear the display. Whirlpool Cabrio Control Board

Potential Causes • Check the Water Temperature Sensor, Heating Element and Element Relay • Check connections to the Sensor, Heating Element and Relay Replace failed component. Door switch open while door is locked. 1. Check for continuity of the User Interface harness. 2. check over here F1 - Control Board Failure - Replace control board (clock).

Press 'Stop/Cancel' to clear display. Whirlpool Cabrio Dryer F1 Error Code Recall Potential Causes • Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. • Check Wire Harness connections to the MCU, the Check for conformal coating on serial communication pins between the machine controller and the motor controller.

Check the inlet valve and pressure switch for proper shut off and operation.

Check connection to water heater. 3. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Verify CCU operation by running a Diagnostic Test or any cycle. Why Does My Whirlpool Cabrio Washer Says F1 Check connections at control and at the latch switch and door switch. 2.

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Electronic Board and the valve for steam fill. 4. This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch. this content Check the drive system for any worn or failed components and reconnect power and plug unit in.

codes. Short circuit of Heater to Ground. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. Plug in washer or reconnect power. 6.

Check the drive motor for powered rotations. 8. Plug in washer or reconnect power. 6. Unplug washer or disconnect power. 2. I'm getting the famous F1 error code that everyone else has gotten and Whirlpool is NOT standing behind their product, they told me all parts and labor will have to be

Measure door switch (door open = switch open small low voltage terminals). Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). If ok, replace probe. F1E1 Error - Main control fault.

F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. Check door switch/lock unit for foreign objects. 2. Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Press PAUSE/CANCEL twice to clear the display.