How To Fix Whirlpool Cabrio Dryer Error Codes F31 Tutorial

Home > Whirlpool Cabrio > Whirlpool Cabrio Dryer Error Codes F31

Whirlpool Cabrio Dryer Error Codes F31

Contents

The doorswitch may cause an interference for the powersupply of the MCU. Check the drive motor for powered rotations. 6. The machine will drain for 3 minutes before unlocking the door. 3. The Steamer will no longer function for any wash cycle and should be replaced. weblink

S. Check the drain pump filter for foreign objects. 5. Unplug washer or disconnect power. 2. Or just drag it here! http://www.justanswer.com/appliance/7s3rm-does-code-f31-mean-whirlpool-cabrio-dryer-moed.html

Whirlpool Duet Dryer Error Code L2

In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared. Verify CCU operation by running a Diagnostic test or any cycle. If code re-appears, replace control board (also called ERC or clock). Check the drive system for any worn or failed components. 4.

Turn off hot and cold water faucets and unplug the unit before servicing. 1. Instant Access! Locate the high limit thermostat. Whirlpool Cabrio Dryer Troubleshooting Codes If the resistance is OK, check P14-3 and P14-6 to machine ground.

Check Pressure Switch harness for continuity. 2. F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. Check connections at control and at the latch switch and door switch. 2. http://www.appliancepartspros.com/answers-for-whirlpool-control-sahara-de-wpw10174745-ap6016286-question-142452.html Click Here to Sign Up!

Check wire connections at the machine control electronics and thermistor. I want to check if the the heater is always on or it pulses on or off by the control electronics. Please help. Check sensor, sensor harness and sensor harness connection at sensor and oven control.

Whirlpool Duet Dryer F 31

NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. http://www.fixya.com/support/t19681691-whirlpool_cabrio_dryer_error_code_f31 Visually check that the P5 connector is inserted all the way into the machine control electronics. Whirlpool Duet Dryer Error Code L2 If it shows continuity, it will need to be replaced and is available below. Whirlpool Cabrio Dryer F1 Code Slowly remove the drum belt from the spring-loaded belt switch tension pulley, gently letting the belt pulley down. 5.

Ask Loading...Oops :Please try again. http://compaland.com/whirlpool-cabrio/whirlpool-cabrio-dryer-error-codes-af.html Tell us some more! Door switch open while door is locked. 1. Check the MCU by looking for operations of the drive motor. 7. Whirlpool Cabrio Dryer L2 Code

Access the machine control electronics and measure the resistance across P8-4 and P9-1. Check all hoses for possible leaks. 6. Download your simple guide to fixing your non-heating dryer by subscribing to my newsletter. check over here you may have something between the tubs or your bearing is going bad .

Ran for 2-3 minutes and stopped again. Normal thermistor resistance values: 60° F. - 15.3K ohms. 70° F. - 11.9K ohms. 80° F. - 9.2K ohms. Functionality is verified with a beep each time the door is closed and opened, and a number and letter appears in the display (i.e., 0E, 09).

Catriver.

Check all hoses for possible leaks. 5. B. Guess: When it was clogged, something got too hot. Heat will not shut off: 1.

F3 - E1 Oven temperature sensor (RTD) shorted (upper oven, if double oven) F3 - E2 Oven temperature is too high (Cook mode) F3 - E3 Oven temperature is too high TEST #4 Heater This test is performed when either of the following situations occur: Dryer does not heat Heat will not shut off This test checks the components making up the F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. this content This fault code will ONLY appear when in the diagnostic test mode.

Press STOP/CANCEL to clear the display.

Refrigerator 25 Cu. Replace Central Control Unit if drum is not moving. Sd SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 If there is no continuity, check the continuity of the power cord for power cord’s L1 wire.

If the above does not correct the problem, go to step 7. 7. Unplug washer or disconnect power for two minutes. Sign in to make your opinion count. Check door switch contacts. 5.

Perform the Console Buttons and Indicators Diagnostic test to verify repair. 9. Check the water temperature sensor and connection to it. 3. Check the drain hose and make sure it is not plugged or kinked. 2.