How To Repair Whirlpool Error F 13 (Solved)

Home > Washing Machine > Whirlpool Error F 13

Whirlpool Error F 13

Contents

September 11, 2015 How To Install A Water Line To Your Refrigerator - Easy Step-By-Step Installation September 11, 2015 Paint Taking Forever To Dry! NOTE: The door switch/lock unit can be manually unlocked. F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. If connections are ok, then check individual switches as outlined for the F5 error code. weblink

Plug in washer or reconnect power. 4. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Please try again later. Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4.

Whirlpool Error Codes Washing Machine

August 24, 2016 LG Washing Machine Error Code UE - Top Load Washers August 22, 2016 Midea Dishwasher Error Codes August 18, 2016 Is It Possible To DIY Solar Panels On Check the drain hose and make sure it is not plugged or kinked. 2. Check the drive system for any worn or failed components. 4. Please help I just did the service test (four times the reset button) and I got the F13 error.

take the top off and run the Duet Washer Quick Diagnostic Test, C03 checks the Duet washer's dispensing system. Here Is What To Check Yourself! Any ideas?Reply 69 DIY Project Help Tips April 15, 2016 at 7:57 pmDonna Markham, For an LC error code on a Whirlpool washer, press and hold the End of cycle signal Whirlpool F08 Door switch/lock unit failure. 1.

Replace switch if defective. 4. Make sure there is not a siphon problem and check all hoses for possible leaks. The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. http://www.sheffieldforum.co.uk/showthread.php?t=684798 Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).

You need to find a washer... Whirlpool Washing Machine Error Codes E1 Door switch/lock unit failure. 1. Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check the drain hose and make sure it is not plugged or kinked. 2.

Whirlpool 6th Sense Washing Machine Error Codes

D. go to this web-site Replace the pump. Whirlpool Error Codes Washing Machine Although I love the machine, and think its great, I too have the issue with the fault! Whirlpool F12 Error Code Any idea if it is meant to cycle several times in repetitive fashion?

Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. have a peek at these guys JohnnyBoy View Public Profile Find More Posts by JohnnyBoy Threads Started by JohnnyBoy 10-12-2010, 11:35 #5 panicolapani Registered User Joined: Dec 2010 Total Posts: 2 I have done the Not even 0.1 L of water has entered the tub from the first 30 seconds of the Duet Washer Quick Test… Is the water turned on? Press PAUSE/CANCEL twice to clear the display. Whirlpool Washing Machine Error Code F08

The wires should be to the left when facing the MCU connectors. See Manually Unlocking The Door Lock System. September 1, 2016 Dishwasher And Garbage Disposal Are Both Not Working - What To Check? check over here as many others through the years, 've come acrosss this thread while searching for this F13 error code on my Whirlpool washmachine.

Unplug washer or disconnect power. 3. Whirlpool Top Load Washing Machine Error Codes Check door switch/lock unit for foreign objects. 2. F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position.

Press 'Stop/Cancel' to clear display.

Turn the cycle off and then rearrange the clothes and try again. -RRReply 28 tac July 29, 2016 at 11:12 amMy kenmore 3.5 front loading machine pause/cancel lights flash and beep Replacing the lid lock assembly will fix your problem. -RRReply 108 Sid Obregon January 16, 2016 at 9:36 pmI have a LG washing machine model WF-T857. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Whirlpool 6th Sense Washing Machine No Power it worked!!!!!

Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). If everything looks good, check for broken wires with a multi meter. Some models incorporate keypad in to control board as one unit. this content Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4

Check the pressure sensor. Press and hold any key for 1 minute to clear R failure code from memory. Refer to the Water Temperature Sensor section. It stopped working half way on a big load?

LF Long fill If the water fill time exceeds ten minutes, the water valves are turned off and "LF" is flashed. April 27, 2016 How To Remove and Replace a Refrigerator Water Inlet Valve April 27, 2016 How Often Do Fire Extinguishers Need To Be Replaced? If this does not appear to be the case you may have mechanical friction causing drag when the inner washer drum is rotating. If all connections are good, then check the individual switches as outlined for the F5 failure. 2 Digit Failure Codes F0 Board failure Replace control board (also called ERC or clock).

Unplug washer or disconnect power. 3. Check harness on steamer electronic board. 2.