(Solved) Whirlpool And Error Codes Tutorial

Home > Error Codes > Whirlpool And Error Codes

Whirlpool And Error Codes

Contents

Lid lock/switch assembly HC Hot and cold fill hoses are reversed Check the positions of the fill hoses on the back of the washer. Turn off hot and cold water faucets and unplug the unit before servicing. 1. Circuit Board Medics 41,360 views 9:57 Troubleshooting and Repairing the F11 Error Code in a Whirlpool Duet Washer - Duration: 6:19. If there are no problems, you usually need to replace the door lock assembly. weblink

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. Press PAUSE/CANCEL twice to clear the display. Plug in washer or reconnect power 7. The doorswitch may cause an interference for the powersupply of the MCU.

Whirlpool Washer Error Codes F21

If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Loading... Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU).

Error Code Possible Solution dET The detergent dispenser cartridge is not detected in the dispenser (only on select models).If you are usingsingle-load doses of detergent, ignore this message. Replace switch if defective. 4. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. Whirlpool Washer Error Codes A10 Unplug the washer and check the wiring harness connections on the main electronic control board and the shifter actuator.

Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. Whirlpool Top Load Washer Error Codes F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. The lid switch must be opened at least once before restarting the cycle, if this condition occurs. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Add to Want to watch this again later?

E2 - Shorted Thermistor - Replace thermistor. Whirlpool Duet Washer Error Codes F20 Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. If the wiring harness connection is okay, then the inlet water valve assembly will usually need to be replaced. If failure still present: 3.

Whirlpool Top Load Washer Error Codes

NOTE: Detects by weight. Find more information onHE Detergent use in your Washer. Whirlpool Washer Error Codes F21 Verify there is not a siphon problem. 2. Whirlpool Washing Machine Error Codes E1 F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs.

Unplug washer or disconnect power. 8. have a peek at these guys Press STOP/CANCEL to clear the display. Press PAUSE/CANCEL two times to clear the display. 1. rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. Whirlpool Duet Dryer Error Codes

Check the wire harness connections for the lid lock/switch assembly on the main electronic control board. If the basket still won't engage, check the drive system for an obstruction or failure. If that works the your pump is highly suspect. check over here Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands.

C. Whirlpool Dryer Error Codes F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. SamuraiRepairman 170,383 views 6:19 kenmore front load washer he4t error code FH - Duration: 10:51.

Possible Causes/Procedure Door lock mechanism is broken or removed from door.

F7 Function key stuck on ERC Replace control board (also called ERC or clock). F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. Short circuit of Heater to Ground. Whirlpool Top Load Washing Machine Error Codes Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check for plugged

All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD). Sign in Transcript Statistics 7,061 views Like this video? Er - Processor Reset Error - This error will only occur if the unit fails to save cycle information during a power outage. http://compaland.com/error-codes/whirlpool-wfw8300sw00-error-codes.html Press CANCEL and observe for 1 minute to ensure operation is correct. 6.

If not, then examine the drive system and eliminate the cause of friction. Replace failed component. F61 STEAMER COMMUNICATION FAILURE An incorrect or corrupted communication between Central Control Unit (CCU) and steamer electronic board is recognized. Check the drain hose and make sure it is not plugged or kinked. 2.