Repair Whirlpool Error (Solved)

Home > Error Code > Whirlpool Error

Whirlpool Error

Contents

See the repair guide to fix it yourself Door lock assembly F/dU Door unlock error The washer won't unlock. F26 DOOR SWITCH ERROR If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds. Refer to the Continuity tests. Reset the oven and see if that fixes it, and if not, replace the control board.For a lot of Whirlpool ovens, you have to replace the clock along with the control weblink

If there are no stored errors 888 will be displayed with 3 beeps. F8E2 Error Dispenser fault. Click here for more details. With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. try here

Whirlpool Top Load Washer Error Codes

Appliance Princess 3,184 views 2:58 Whirlpool Wall Oven Repair - Neither Ovens Will Bake - WW2780W - Duration: 31:48. E1 - Open Thermistor - Replace thermistor. Press STOP/CANCEL to clear the display. ^ top LS Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly. F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1.

Do not add more detergent, as the clothing should already be penetrated with water and detergent. The failure will be reset after running the Diagnostic Test Program. 1. Remove clothes from drum and start the cycle again. Whirlpool Dryer Error Codes Main electronic control board, User interface control F3 E1 Water level pressure sensor fault Unplug the washer.

Loading... Replace failed component. Close lid and press START/PAUSE. http://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/Error_codes_in_front_load_washers Unplug washer or disconnect power. 2.

F2-E1 - Touch Pad (Keypad) Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Whirlpool Range Error Code F9e0 Press PAUSE/CANCEL to clear display. Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. This may signify problems with the drive motor, thermal protector or motor controller.

Whirlpool Washer Error Codes F21

F9 - Oven Door Lock Failure - Check door lock switches and wiring. you can try this out This should clear the unit of the excess detergent. 1. Whirlpool Top Load Washer Error Codes If corrections are made during any step, power should be reconnected and the unit should be tested. Whirlpool Washing Machine Error Codes E1 F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1.

The door should now be unlocked. http://compaland.com/error-code/whirlpool-ac-fc-error.html Household power supply is too low. 2. mike webb 1,705 views 1:49 E1 f5 code oven - Duration: 1:51. After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. Whirlpool Top Load Washing Machine Error Codes

Disconnect power and unplug unit to check door switch/lock unit. LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display. F7 Function key stuck on ERC Replace control board (also called ERC or clock). check over here In normal use (a little blockage is normal) the steamer cleans itself.

F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Whirlpool Oven Error Codes E2 F3 Drive motor, Main electronic control board F2 E1 Stuck key This code is for models with a digital display. FL - Flood Condition - FL error code will appear when the unit detects an overfill, or excessive amounts of water in tub.

Unplug the washer and check the drain pump for a clog.

Jay Dornbos 5,738 views 1:51 How to fix a Kitchenaid/Whirlpool Oven that won't turn on and won't open - Duration: 15:06. If the wiring harness connection is okay, then the inlet water valve assembly will usually need to be replaced. Lid lock/switch assembly, Lock strike F5 E4 Lid not opened between cycles If the washer is started several times without the lid ever being opened, then this code appears. Whirlpool Duet Dryer Error Codes Replace door switch.

Drain pump Wash LED on No fill or long fill Water isn’t being detected as entering the washer. CA or CI Average current limit or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. this content Check the fill hoses and inlet water valves.

A power glitch may cause this error. This should clear the unit of the excess detergent. 1. Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. If the basket spins properly, unplug the washer and check the wiring connections on the actuator.

Unplug washer or disconnect power. 3. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness To Manually unlock the door lock system: 1. MAIN RELAYS ERROR One of the main relays is not working properly.