Repair Whirlpool Error Codes F2 (Solved)

Home > Error Code > Whirlpool Error Codes F2

Whirlpool Error Codes F2

Contents

Check the MCU by looking for operations of the drive motor. 5. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. F2 will appear. http://compaland.com/error-code/whirlpool-error-codes.html

Honolulu, HI About Us DIY Blog Our Story Core Values Locations Rave Reviews Affiliates Program Job Listings My Account Sign In My Account Order History Shopping Cart Our Policies Terms of After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. Jayne Killackey // Dec 20, 2015 at 11:20 am Hi Gene, I have a 22 year old XL44 GE gas range. Also it does this 1-2 times on warm up, after that it will bake/broil like normal.

Whirlpool F2 Error Washer

In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Gene. Check the drain hose and make sure it is not plugged or kinked. 2. Check sensor, sensor harness and sensor harness connection at sensor and oven control.

Video kiralandığında oy verilebilir. Imi Chitterman 101.681 görüntüleme 1:07 Checking an Oven Temperature Sensor - Süre: 3:58. F9 - Oven Door Lock Failure - Check door lock switches and wiring. Whirlpool Washing Machine Error Codes E1 Check probe.

Seth // Sep 16, 2015 at 7:22 pm My oven is also continuously flashing the F2 error, I will have to flip the breaker to get it to stop so I See Long Drain. Please verify the model number and resend it to me. Beeping stopped and ERC panel is dark.

Check for stuck lock switch. W10114388 Christina // Feb 13, 2016 at 6:42 am I pulled off the back panel and noticed that the fibreglass insulation looks burnt..lol! Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Refer to the Continuity tests.

Whirlpool Oven Error Code F9e0

Check that the serial harness at the MCU is not mounted upside down. http://www.appliancehelponline.com/whirlpool.html Like ApplianceAssistant on Facebook! Whirlpool F2 Error Washer If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Whirlpool Oven Error Codes E6 F2 F2-E1 - Touch Pad (Keypad) Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.

Door lock mechanism is broken. have a peek at these guys I'm a mom who is prettygood with electronics and can take just about any appliance apart. I screwed it in tight to the frame to make sure the ground was solid and the oven was fixed! Gene // Jun 3, 2015 at 3:25 pm Hello Kirsten. Whirlpool Oven Error Codes E2 F3

NOTE: Detects by weight. Plug in washer or reconnect power. 5. This condition occurs when excessive water in the tub causes the overfill switch to trip. check over here If failure occurs during high-speed spin the door unlocks after 3 minutes. 1.

Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2. Whirlpool Top Load Washer Error Codes Note: Applies to all F1-E... F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect.

Replace sensor if found defective.

resolved our issue. My husband is out of town and I cannot pull the oven out by myself. Replace probe if all else checks out ok. W10114387 Used the over 3 times and it's throwing the f2 code and running away again, had to flip the breaker to shut it down.

drtom4444Apr 10, 2011, 10:49 PMCheck your vent, it sounds as if it is clogged. Press PAUSE/CANCEL two times to clear the display. 1. Check sensor, sensor harness and sensor harness connection at sensor and oven control. this content The lid switch must be opened at least once before restarting the cycle, if this condition occurs.

Press 'Stop/Cancel' to clear display. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU If this happens, replace oven control (also called clock or ERC). 2.