How To Repair Whirlpool E3 F2 Error (Solved)

Home > Error Code > Whirlpool E3 F2 Error

Whirlpool E3 F2 Error

Contents

The techsheet for our unit says we have a "Shorted key error". F1-E3 - Wiring Harness Cavity Size Does Not Match Stored Value - Check the jumpers in the harness to make sure they agree with the actual oven size. All rights reserved. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU weblink

Check wires and connectors from control to latch switch, then from latch switch to control. Press and hold any key to clear the error code and F2 code should appear. Ste. 500, Encino, CA 91436 1-877-477-7278 Tennessee 240 Edwards St. Click here for more details. http://www.shopyourway.com/questions/1154991

E3 F2 Error Code Whirlpool Washer

Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Press STOP/CANCEL to clear the display. ^ top CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit

If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. If this happens, replace oven control (also called clock or ERC). 2. E1 - Open Thermistor - Replace thermistor. Whirlpool Oven Temperature Sensor If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective.

I had so many questions and they answered them all." Sharon S. Whirlpool Oven Error Codes E2 F3 Single Wall Oven w/ True ... Also check the motor and wire harness. view publisher site By Model Number By Part Description By Part Number powered by AppliancePartsPros.com « Removal of built-in ovens from cabinetry | David » Thread Tools Show Printable Version Email this Page

F1 Board failure Replace control board (also called ERC or clock). Whirlpool Oven Error Code F3 The lid switch must be opened at least once before restarting the cycle, if this condition occurs. Check connections at control and at the latch switch and door switch. 2. I turn the oven off on the control panel and the broiler element stayed on.

Whirlpool Oven Error Codes E2 F3

F09 Overflow condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. http://producthelp.whirlpool.com/Troubleshooting_Guides/Troubleshooting_for_Top_Load_HE_Washers_(Electronic_Control)/Error_Codes/F%23_E%23_or_F%23%23/F2_E3_Error_code_for_top_load_washers Password Show Threads Show Posts Register | FAQ's | New Posts | Today's Posts | Extras Go to Page... Appliance Repair Forum > Appliance Repair Help > Oven E3 F2 Error Code Whirlpool Washer F14 EEPROM error The Central Control Unit (CCU) receives it’s data from an EEPROM onboard the CCU. Whirlpool Self Cleaning Oven Error Codes E3 F2 Undo dodge59 You don't mention how old your oven is Madymo3d, but an oven that is stuck on, is definitely a "Safety hazard".

If failure remains, disconnect power and replace control. http://compaland.com/error-code/whirlpool-02-f-error.html Get more answers from the people in your networks Tags Wall Ovens , Whirlpool , Appliances Click to remove this tagging. What's New? See Details Whirlpool 5.0 cu. Whirlpool Oven Error Code F9e0

All rights reserved. © Applianceblog.com 2004 - 2016 Login|Contact Us Appliance Need Appliance Repair Help? Select 'cancel' and observe for one minute for errors. Check for stuck lock switch. check over here Does anyone have any idea what these might be?

All rights reserved. Whirlpool Accubake Oven Error Codes Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. With an overfill condition, the beeper repeats a warning every 10 seconds with no time out.

To start viewing messages, select the forum that you want to visit from the selection below.

Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. F2 will appear. I don't need a man in my house, all I need is a Sears expert online:) by Manage My Life March 11th, 2012 Comment 0 votes Didn't find what you are Whirlpool Oven Error Code F3e2 Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the Opening the lid will allow you to view and redistribute the load. If damage is found, replace appropriate part. http://compaland.com/error-code/whirlpool-ac-fc-error.html Press PAUSE/CANCEL twice to clear the display.

FdU Door unlock error A Door Unlock Error occurs if the door cannot be unlocked. Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. Thanks for your help. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up &

Earned 106,756 community points in Click'>Appliances September 19th, 2012 Comment 0 votes Lyle, are we talking about the touchpad (part number 4451348)? I can't find Part Number 4451347. Replace control board (clock). If door is NOT latched, disconnect power from unit and check wires and connections. Check the inlet valve and pressure switch for proper shut off and operation.

Virginia Beach, VA "Your service people are so friendly and helpful. i hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours. Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected.

Press STOP/CANCEL to clear the display. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). whirlpool gold microwave oven wall unit. 1 answer Popular Products in Whirlpool Whirlpool 5.0 cu. Earned 106,756 community points in Click'>Appliances September 26th, 2012 Comment 0 votes Didn't find what you are looking for?

This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Flashing Display Time - Open Lid - This will only occur if the lid is opened during a running cycle. Houzz The new way to design your home™ Help Remember Me? Have you ever purchased from PartSelect.com before?