How To Repair Whirlpool Duet Washer And Dryer Error Codes Tutorial

Home > Error Code > Whirlpool Duet Washer And Dryer Error Codes

Whirlpool Duet Washer And Dryer Error Codes

Contents

Washing Machine Service Repair Manuals Online Your washing machine is not working properly. Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). Loading... Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). weblink

Unplug the washer and look at the drain pump and hose to be sure it is not clogged. Replace the heater element. F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral. Is it F43 or does it appear exactly as f0043? -RRReply 31 David Gourlay July 18, 2016 at 12:50 pmSears, Kenmore - Elite, front load washing machine made by Samsung. http://applianceassistant.com/Washer-Repair/Duet/Duet-Washer-Error-Codes.php

Whirlpool Top Load Washer Error Codes

The door may now be opened. Check the resistance across the the two pump terminals with an ohm/voltage meter. A washing machine making a loud noise when spinni...

F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. Bill Newberry 713,349 views 10:43 WHIRLPOOL DUET / MAYTAG WASHER MACHINE repair error codes F01,F06,E01,E02 - Duration: 3:15. Whirlpool Duet Dryer Error Codes Youtube Icon Facebook Icon Twitter Icon Terms of SaleTerms of UsePrivacy Policy Need Help?

Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check for plugged Whirlpool Duet Washer Error Codes F21 August 24, 2016 LG Washing Machine Error Code UE - Top Load Washers August 22, 2016 Midea Dishwasher Error Codes August 18, 2016 Is It Possible To DIY Solar Panels On Unplug the washer for 5 minutes, restore power and see if the code clears.

If the outlet cannot be reached, turn the circuit breaker to the unit off. -With the power disabled to the washer, press and hold the START/PAUSE button for 5 seconds. -Plug

Locate the water faucets that go to the washer. Whirlpool Duet Washer Error Codes F02 If door not latched: A. If the above does not correct the problem, go to step 7. 7. It will try to unlock the door 6 times before displaying the error.

Whirlpool Duet Washer Error Codes F21

B. http://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-duet-high-efficiency-front-load-washer-error-codes.html Make sure all grounding switches are engaged. 3. Whirlpool Top Load Washer Error Codes Loading... Whirlpool Duet Reset In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared.

What does this mean 500 series 9000464931Reply 90 DIY Project Help Tips March 11, 2016 at 9:41 pmjudy, Bosch error code E is an error that means your main control board have a peek at these guys Remove the lower bottom cover of the washer. Potential Causes • Check the Water Temperature Sensor, Heating Element and Element Relay • Check connections to the Sensor, Heating Element and Relay Replace failed component. Need A Tech Sheet or User Manual For A Whirlpool Duet Washer WFW70HEBW? Whirlpool Duet Washer Error Codes F20

If "Sud" is displayed a potential suds lock is detected. Unplug the power cord from the outlet. 2. If there are you are using too much detergent or the wrong detergent. check over here The BD34 or D34 error code is not in the database.

I changed to rapid wash with a 30 minute cycle and it worked okay. Whirlpool Duet Washer Error Code F11 Points valid for 14 days. FdL Door lock error A Door Lock Error occurs if the door cannot be locked.

If the outlet thermistor is defective, replace it.

Check if the airtrap is not blocked. 3. If the above does not correct the problem, go to step 7. 7. F2 will appear. Whirlpool Washer Error Codes 5d What does that mean?

F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. Perform Service Cycle to pair the UI and CCU SW. 2. Unplug the dryer and check the resistance of that thermistor, which should be about 10,000 ohms. this content Different model numbers can mean different errors.

Remove any blockage from the drain hose, drainpipe or utility sink. Get all the details Close 365 Day Return Policy You may return an unused and uninstalled part in its original packaging. Unplug washer or disconnect power. 2. The pressure switch is not tripped after 6 minutes.

To return a part, you must first obtain a Return Authorization number by calling 888-205-0966 or visiting our website at www.SearsPartsDirect.com and chat with a Parts Trusted Advisor. Opening the lid will allow you to view and redistribute the load. Do this three times. The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω.

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the Any ideas?Reply 47 DIY Project Help Tips June 7, 2016 at 9:59 pmPaul, Make sure your hot and cold water faucets are turned on. Subscribe ApplianceAssistant on Youtube! Search Site For Parts Call (877) 338-6774 Like ApplianceAssistant on Facebook! Check the motor and do a continuity test. 3.

Check the pressure switch. 8. F10 Motor Control Unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink Unplug the unit to service. Make sure all grounding switches are engaged. 3.

F9E1 will be showing if the washer is not draining properly. Discount will be automatically applied during check-out.