How To Fix Whirlpool Duet Error Code F27 (Solved)

Home > Error Code > Whirlpool Duet Error Code F27

Whirlpool Duet Error Code F27

Contents

Household power supply is too low. 2. If after 30 seconds not minimum 0.1l of water entered or maximum fi ll time of 13 minutes is exceeded, the valves will be turned off and the error code will Check the water temperature sensor and connection to it. 3. Check the drive motor for powered rotations. weblink

Check the drive motor for powered rotations. 8. F62 STEAMER ELECTRONIC BOARD RELAYS ERROR One of the steamer relays (K1, K2, K3, K4) on the Steamer Electronic board have failed, there is an open or short circuit. To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. F2 Oven temperature is too high 1. http://www.shopyourway.com/questions/1087402

Kenmore F27 Error

Check for continuity of the User Interface harness. 2. If you are using HE detergent, HOW MUCH are you using? Started by stocpro47 Replies: 10Views: 3230 July 29, 2013, 03:53:35 PM by stocpro47 whirlpool duet steam,wfw9500tw02 error 70 ccu? NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1.

Check mechanical linkage from dispenser motor to the top of the dispenser. 3. F35 ANALOG PRESSURE SENSOR FAILURE If this failure is displayed, there is any malfunction of the steamer component detected by the Steamer Electronic Board. 1. If the condition continues four times, the F31 code will show. 1. Unplug washer or disconnect power for two minutes.

Push the door and check if it is completely closed. 2. Whirlpool Front Load Washer Error Codes F23 HEATER FAILURE If the temperature increase during the first 40 minutes is less than 86°F (30°C). 1. Loading... http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU).

Short circuit of Heater to Ground. Click here for Fujitsu repair information. Check doorswitch system. (See checklist of F26 and F29). Check sensor, sensor harness and sensor harness connection at sensor and oven control.

Whirlpool Front Load Washer Error Codes

Replace User Interface. Check the inlet valve for proper shut off. 7. Kenmore F27 Error F23 HEATER FAILURE If the temperature increase during the first 40 minutes is less than 86°F (30°C). 1. Whirlpool 6th Sense Washing Machine Error Codes This condition occurs when excessive water in the tub causes the overfill switch to trip.

Press PAUSE/CANCEL twice to clear the display. have a peek at these guys Open and close the door. 2. Replace the Motor Control Unit. NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. Whirlpool Washer

Door switch/lock unit failure. 1. MAIN RELAYS ERROR One of the main relays is not working properly. By reading any content on this site you agree to AppliancePartsPros.com , Inc. check over here Unplug washer or disconnect power. 2.

Replace User Interface. The failure will be reset after running the Diagnostic Test Program. 1. F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage.

Parker Oct 13, 2013 I did everything suggested above.

If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Check for drain pump failure. 6. This might clear any debris. Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table on page 10.

Autoplay When autoplay is enabled, a suggested video will automatically play next. The washer does not flash "PF" when it is first plugged in. ft. this content In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared.

Remove the air hose from the water level switch, and blow into the hose,as hard as possible, to clear any debris that may have accumulated in the hose. The wires should be to the left when facing the MCU connectors. Check door switch/lock unit. 3. Nov 30, 2009 | Whirlpool Duet GHW9150P Front Load Washer 1 Answer F21 Error Code on Whirlpool Duet & Kenmore Elite Front Loader Washers This helped my husband fix our washer.

PartSelect 147,377 views 14:54 Locating and Repairing a Leak in a Front Load Washer - Duration: 6:16. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. MAIN RELAYS ERROR One of the main relays is not working properly. The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed.

If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. If there is an error reading this data it will cause this error. F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down.