Fix Whirlpool Appliances Error Codes (Solved)

Home > Error Code > Whirlpool Appliances Error Codes

Whirlpool Appliances Error Codes

Contents

Loading... If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). Verify that the inlet valve is operational. http://compaland.com/error-code/whirlpool-error-codes.html

In the case Whirlpool dishwasher not draining, refer for technical help to dishwasher repair shop Whirlpool. The failure will reset after running the Diagnostic Test Program. 1. If the above does not correct the problem, go to step 7. 7. F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU),

Whirlpool Washing Machine Error Codes E1

Once the allotted time is exceeded the machine will light the "Clean Filter" indicator. If that doesn’t work, you need to replace the door switch so it recognizes the door is closed.What happens if the control lock LED is on but it doesn’t do anything?The B. Check the drain hose and make sure it is not plugged or kinked. 2.

Check the drive motor for powered rotations. 8. You can find that on the rating plate inside the door. The control should not allow the unit to run in this condition. Whirlpool Oven Error Codes E2 F3 Can you help me?

If failure remains, disconnect power and replace control. This may signify problems with the drive motor, thermal protector or motor controller. Re-apply power and observe for at least one minute. 3. http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx Check for continuity of the User Interface harness. 2.

No Water In Your Washing Machine Check that the water supply to the washing machine is okay and there is water Check for kinks in the fill hoses to the washing Whirlpool Range Error Code F9e0 Mechanical water indicator WI Spray pump works, the WI switches more than 20 times in 2 minutes backOptical Water Indicator Always after the OWI - signal is missing the electrical components This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds. If you are unsure please ask in the forums as well as for all other Whirlpool washing machine fault codes but we think that these codes relate to many of the

Whirlpool Top Load Washing Machine Error Codes

F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong). http://www.how-to-repair.com/help/how-to-enter-test-mode-on-whirlpool-awod-awd-series-repair-faults-test-errors/ Also check the motor and wire harness. Whirlpool Washing Machine Error Codes E1 F7 Function key stuck on ERC Replace control board (also called ERC or clock). Whirlpool 6th Sense Washing Machine Error Codes Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5.

The washing machine will time out on drain after approximately four minutes when it will switch to what is known as impulse draining where the pump will run for ten seconds, have a peek at these guys FAULTSCAUSESOLUTION F1NTC break Temperature out of the normal value (-3°C till +85°C)1. Repair Guides Frequent Questions Log In Account Cart HOMEWASHING MACHINE Accessories & miscBeltsCabinet PartsDoor PartsDrum PartsElectrical PartsHoses & PipesKnobsMotor PartsPump FiltersSeals GasketsSuspension Parts TUMBLE DRYER Accessories & miscBeltsCabinet PanelsDoor PartsDrum PartsElectrical Door lock mechanism is broken. Whirlpool Washer Error Codes F21

Water inlet valve mechanically not closed 2. The control should not allow the unit to run in this condition. If no damage to wires and all connectors okay, proceed to step C. check over here Look for welded relay contacts on bake or broil relays.

In the 1989, the Europe Whirlpool company, which later came to belong only to Whirlpool Corporation, was created by the concerted efforts with Philips. Whirlpool Washing Machine Error Code Pe F34 UNLOAD INDICATION This failure is only for information and can be displayed in the error history during the Diagnostic Test. Press STOP/CANCEL to clear the display. ^ top LS Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly.

in 10 sec.) 2.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. Unplug washer or disconnect power. 3. Whirlpool Split Ac Error Codes The motor control unit has detected an overheat situation.

Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. Replace also the CCU. this content Verify flow meter operation by blowing air through the part and measuring the resistance. 8.

See Manually Unlocking The Door Lock System. Relays (RE2) on control board (CB) is defective 4. Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check for plugged NOTE: The door switch/lock unit can be manually unlocked.

Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check