Repair What Error Code Identifies A Floppy Drive Problem (Solved)

Home > Error Code > What Error Code Identifies A Floppy Drive Problem

What Error Code Identifies A Floppy Drive Problem

Contents

Click System. If the floppy works, it is possible the hardware that was added may be conflicting with the floppy drive.Re-configure the new hardware, and try replacing it to see if the problem Use the HP support document Using PC Doctor to learn more about testing for floppy drive failures. CraytonYayıncıCengage Learning, 2008ISBN1584506091, 9781584506096Uzunluk656 sayfa  Alıntıyı Dışa AktarBiBTeXEndNoteRefManGoogle Kitaplar Hakkında - Gizlilik Politikaları - Hizmet Şartları - Yayıncılar için Bilgiler - Sorun bildir - Yardım - Site Haritası - GoogleAna Sayfası Back http://compaland.com/error-code/what-is-error-code-50-on-a-mac.html

System Board Errors: Code Description 101 System board interrupt failure (unexpected interrupt) 102 BIOS ROM checksum error (PC, XT); timer error (AT, MCA) 103 BASIC ROM checksum error (PC, XT); timer One possible beep code (code 1-3-1) consists of one beep, a burst of three beeps, and then one beep. Bios Central is a trademark of Bob Hurt. The drive may be damaged. http://www.techrepublic.com/forums/discussions/floppy-drive-failed-40-error-on-startup/

Ibm Error Codes

Any other ideas are welcome! 0Votes Share Flag Collapse - Follow these steps by Jacky Howe · 8 years ago In reply to All of the above ? :( It could Enter system setup to review your computer's configuration information, and ensure that the device you want to test displays in system setup and is active. This test typically takes 10 to 20 minutes and requires no interaction on your part.

It may be possible to recover the disk: Turn off the PC and unplug the power cord. Bad error-correction code (ECC) on disk read — See "Drive Problems" in your Owner's Manual. On some early Presario models, this may be the F10 key. Ibm Checkpoint Codes On the back of the floppy drive you will find a red, yellow, and black cable and a flat, gray ribbon cable.

Figure : Floppy disk controller Remove other floppy drive controllers that are listed, if any. How Many Digits Are In A Mac Address? Tab Function Results Displays the results of the test and any error conditions encountered. Then remove the drive from the computer (see Entering System Setup). :\ is not accessible. Check the diagnostic lights to see if the specific problem is identified.

I had several used floppy drives that I tried it with and one of them was new. Parity Error Message HP and Compaq Desktop PCs - Floppy Drive Troubleshooting Troubleshooting the floppy drive Error message: The disk may be write protected Floppy disk is stuck in drive Clicking noise coming from I did try putting the original back in as you suggest but no luck there either. Thanks for any help you can give.Dawn Huber Share Flag This conversation is currently closed to new comments. 10 total posts (Page 1 of 1)   + Follow this Discussion ·

How Many Digits Are In A Mac Address?

Check the diagnostic lights to see if the specific problem is identified. http://support.feelpcs.com/pc-spec/DimensionE510/tshoot1.htm Click System. Ibm Error Codes See your computer Owner's Manual for information on how to contact Dell. 162 Configuration Error Ibm Server X3650 It is advisable to immediately back up your data and replace your hard drive by calling your support desk or Dell — If no replacement drive is immediately available and the

After Windows has fully loaded, test the floppy drive. this contact form See Windows Help for instructions.If a large number of sectors are defective, back up the data (if possible), and then reformat the floppy disk or hard drive. Have also checked the BIOS to make sure the drive was set correctly but no change. If you are still unable to do access your floppy drive then try: Power down the system again and pull the red, yellow, and black power lead off the back of What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

The metal slide cover has probably become bent and is hitting on the inside of the drive. Once in SETUP you need to check that CMOS is identifying your Floppy Drive and that it is the correct one (i.e., 3.5 in., 1.44MB is the current standard for diskette When this switch is in the up position, the floppy disk is write-protected and cannot be written to (see Figure). http://compaland.com/error-code/what-does-error-code-919-mean.html Diskette write protected — Slide the write-protect notch on the floppy disk to the open position.

Attachment failed to respond — See "Drive Problems" in your Owner's Manual. Hdd Controller Failure If the display is connected and powered on, see Diagnostic Lights.If the power light is blinking green, the computer is in standby mode. No it doesn't initialize or seem to spin.

Verify that the floppy connection is connected to the motherboard FDD connector.

Diagnostic Lights CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Error 31 is what I get in device manager when it actually sees the drive. The problem was, these diagnostic codes were never really documented all that well. Floppy Disk Drive Problems If the computer malfunctions, the sequence of the lights helps to identify the problem.

If you contact Dell, technical support will ask for your Service Tag. In Windows 98 and Me, right-click the My Computer icon on the desktop, and then select Properties. If you have two or more memory modules installed, remove the modules, reinstall one module (see Installing Memory), and then restart the computer. Check This Out If you cannot resolve the error condition, contact Dell (see "Contacting Dell" in your Owner's Manual).

The codes that I am presenting here are from documents I have read through, found on the web, found in old books, documents and technical papers. Solid green power light and no beep code but the computer locks up during POST An integrated system board device may be faulty. Make sure the end of the ribbon cable with the red stripe is towards the floppy power connector. Thus 200 means the system memory was tested.

Contact Dell (see your computer Owner's Manual for information about how to contact Dell). In Windows 98 and Me, click the Device tab and select the Manager View devices by type option. Note: If you have a Pentium or PCI system, check the security section of the CMOS and remove the supervisor password if one has been set. At the Dell Diagnostics Main Menu, left-click with the mouse, or press and then , to select the test you want to run (see Dell Diagnostics Main Menu).

Run Express Test first to increase the possibility of tracing the problem quickly. Double-click the type of device for which you are installing the driver. CraytonÖnizleme Yok - 2008The A+ Exams GuideChristopher A. If problems persist, continue to the next step.

Support Forum Join the conversation! In Setup, press F5 on the keyboard to load defaults. But I have some clients who still have old ones and need to be able to read them. I can just give them an external floppy drive but would really like to understand what is going on here.

Run Express Test first to increase the possibility of tracing the problem quickly.